Where to start building a fence from corrugated board. We build a fence from corrugated sheets with our own hands - instructions, drawings, video. Foundation for a fence

If you decide to install a corrugated fence with your own hands, then this review is for you. It describes in great detail and clearly all the nuances of the work process. You just need to repeat all the steps - and the result will be no worse than that of professional builders.

How to organize work correctly

To get a good result, it is not enough to understand only the features of installing a fence made of corrugated board. You need to choose high-quality materials, use the right tools and build a strong supporting structure. We'll walk you through the process from start to finish so you don't have any questions.

Preparatory activities

Going straight to buy materials is not the best solution. Since you do not know the exact quantity, and even a professional will not carry out calculations by eye.

Therefore, do not be lazy and spend half an hour to carry out measurements and calculations:

• First of all, the location of the fence is determined. A construction cord is stretched along the line, which will serve as the main guide. Wooden pegs or metal elements are hammered into the corners, onto which a cord or fishing line is attached;

• Length measurements are taken. First of all, it is worth checking the length of the fence. Everything is simple here, to work you need to attract an assistant and use a tape measure to take all the measurements;

• The pitch of the columns is determined. It can be anything, but most often the range from 2 to 3 meters is chosen, 2.5 meters is the most popular and convenient solution. It is best to immediately mark the position of the supports, so you can accurately calculate the required number of columns;
• The required volume of profiled sheet is calculated. Everything is simple here if you know the dimensions of the corrugated sheets. The standard width is 1155 mm, the useful width is 1100 mm. The height can be any, the material will be cut to the nearest centimeter.

If you have an uneven landscape, you should design the fence to compensate for any level changes. In this case, a strip foundation must be made, with the help of which all irregularities are covered. Below is an example project for an uneven area.

Materials and tools

Even perfect adherence to installation technology does not guarantee the reliability of the fence if you used low-quality materials. Therefore, you need to choose everything you need very carefully. The table below will help you make the right decision.

Installing a fence from corrugated sheets with your own hands requires that you have a certain set of tools:

• Welding machine for attaching wires to poles. A mobile household option operating on a 220 Volt network is suitable. If you don’t know how to cook, it’s easier to hire a welder for an hour or two. In this case, you need to carry out preliminary preparation and marking so as not to waste time and complete the work quickly;
• Grinder for cutting metal and cleaning it before welding. This tool allows you to quickly and efficiently cut a pipe, clean welds and prepare the surface for welding. Don’t forget to stock up on cutting and grinding discs of the appropriate diameter;

• Use tin snips to cut corrugated sheets. Under no circumstances should you carry out work with a grinder; this will cause the profiled sheet to overheat and within a year the ends will begin to rust;

• To dig holes for posts, use a shovel or a special drill with a diameter of at least 20 cm;
• The solution is prepared either manually (in this case you will need a large container) or using a concrete mixer. The second option is preferable for large volumes of work. It is not necessary to buy equipment; you can rent it for 1 day;
• Measurements are made using a tape measure; markings are best done with a felt-tip pen. The most convenient way to control the position of pillars and corrugated sheets is with a building level;
• The sheets are fastened using a screwdriver with a special M8 attachment. It is sold in hardware stores and is designed specifically for roofing screws; the magnetic holder allows you not to lose the fastener during work.

Installation of pillars and fastening of veins

Installation of a corrugated fence begins with the installation of posts.

The process consists of the following steps:

• Digging or drilling holes for poles. The work is carried out with a shovel or drill; the minimum depth of the supports should be at least 1 meter. In addition, a cushion of sand or gravel is poured onto the bottom in a layer of 10-20 cm; this nuance should also not be forgotten. The total depth is usually 120-140 cm;

• A pillow is poured onto the bottom. It will ensure the stability of the installation and will not allow the pillar to sag during concreting;
• The pillar is installed in place. First of all, the height of its above-ground part is checked, and if necessary, the position is adjusted. If the support is low, then sand is added, if it is high, then the column is carefully deepened;

For reliability, protrusions and lintels can be welded to the underground part. Then, when concreting, the pillar will be fixed much more firmly.

• If a filler of stones and bricks is used, then the hole is filled to 2/3 of the depth. The rest should be placed after the initial filling of the solution, when it fills all the voids. The stones are carefully compacted, while the position of the pillar is constantly checked using a level; it must stand level;

• The solution is being prepared. If you don’t have filler, then mix cement, sand and crushed stone in a ratio of 1:3:5, the consistency should be quite thick. If you use stones or bricks, then prepare a semi-liquid solution of 1 part cement and 3 parts sand. The solution must penetrate into all voids and fill them for the best fastening;
• Pillars are being concreted. The solution is poured into the holes and compacted with a stick or reinforcement so that it fills the hole as best as possible and there are no voids left in it. The solution with crushed stone is poured to the top, and if you used stones, then at the first stage they must be closed, after which the filler is added to the very top and the solution is filled to the required level;

• The position of the elements is checked. I know from my own practice that even with careful pouring, the pillar can move. Therefore, immediately after concreting, be sure to check its position with a level on all sides and, if necessary, level it. Only after this can the work be considered successfully completed.

It takes time for concrete to gain strength. It is best to continue work no earlier than 5 days after concreting, during which time the material will set well and harden.

The technology for installing a fence from corrugated sheets with your own hands includes such a stage as fastening the veins. This part of the work can be done in two ways: welding and using special brackets.

Let's look at each of them and start with welding:

• Jumpers and pillars are being prepared. As for the veins, they are cut into pieces that should be 5 mm less than the distance between the posts. The surface of the pillars at the place where the lintels are attached is cleaned; if they are painted, they are removed;
• The veins are exposed and welded. If you have clamps, then the easiest way is to fix the jumpers with their help; if there are no fastenings, then two assistants should hold the element until it is grabbed. Welding is carried out along the entire perimeter of the junction;

• After welding, the seams are cleaned. Too protruding sagging and other flaws are removed. If poorly cooked areas are found, they need to be cooked again;
• The surface is cleaned and painted. If you had painted pillars, then only the joints and veins are painted. If there is no coating, then the entire treatment is performed. The protective composition is applied in at least two layers, special attention is paid to welding areas and other joints.

Now let’s look at the option of connecting pillars and joists using special brackets. You can see what they look like in the photo, and we’ll look at how to use them below:

• The first element is installed at the level you need. Installation to the pole is carried out using self-tapping screws. Fastening can be done on the sides or from the front, it all depends on the design of the fastening unit;
• The bracket is placed on the second post. To accurately determine its position, you need to install a jumper and place a building level on it. The exact location of the fastening is determined from it, and it is screwed to the support. In the same way, work continues along the entire length of the fence;

• The jumpers are fixed with self-tapping screws on the back side. The result is a very strong and perfectly smooth knot. The only disadvantage of this solution is that the fasteners cannot be found in all cities, so if you decide to use this technology, make sure that you can buy the brackets.

Fastening corrugated sheets

Installation of corrugated sheets on the fence is carried out according to the following scheme:

• First of all, a sheet is prepared. If cutting is needed, then marking is made and the element is cut. If there is a protective film on the surface, then it is better to remove it before fastening, since then it will be very difficult to tear it out from under the screws, and pieces of polyethylene sticking out from under the washers will ruin the entire appearance of the fence;

You should also know how to properly secure elements with self-tapping screws. Here you should be guided by the rubber base of the washer; it should not be crushed, but it should not just touch the surface. The correct option is shown in the simple and clear picture below.

• The sheet is placed in the required position and tacked. To begin with, it is enough to tighten 4 self-tapping screws in the corners so that you do not need to hold the element. Next, the corrugated sheet is attached as expected, the hardware should be located through 1 wave, their length is usually 20-25 mm;

• The following sheets are attached in the same way. Do not forget to check the position of each element with a level; many people forget about this after installing the first sheet, and as a result, a noticeable distortion forms at the end of the fence;

• Fence strip attached. It is needed in order to give the structure a more attractive appearance and to cover the upper ends from precipitation. The elements are simply put on the upper part, at the places of their connections an overlap of at least 30 mm is made. Fastening is done using rivets, which are matched to the color of the fence, everything is simple and quick.

Installing a corrugated fence according to this review will not be difficult. If you are interested in the question of assembling gates and wickets, then the process is similar to that described above with the only difference being that you need to weld the frames and attach them to the posts with hinges. This type of work is described in detail in a separate review on our website.

Conclusion

After reading the review, anyone can handle the job, especially since you choose the options for assembling the structure yourself. The video in this article will help you understand the topic even better and will clearly show many important aspects of installation. If you still have questions, write them in the comments below.

Before you make a fence from corrugated sheets with your own hands, you need to understand the labeling of this material. The correct selection of the grade of corrugated sheeting will make the structure reliable and durable.

The profiled sheet is marked with an alphabetic and digital code. There are three letter designations for profiled sheets: S, N and NS. For fences, corrugated sheets with the designation C (wall) are used. Products with the designations H and NS are used for roofing work.

Table of profiled sheet brands.

The numerical designation shows the height of the stiffener in mm, and can vary from 8 to 35. A higher stiffener makes the sheet stronger. For fences, sheets with an edge height of 8 mm can be used, but for fences in places with high wind loads, it is better to take sheets with an edge of 10 to 20 mm.

The thickness of the metal varies from 0.4 mm to 0.8 mm. For a fence, it is enough to choose 0.45 - 0.5 mm.

It turns out that for fencing you should choose profiled sheets of grade C8, C10 or C20, 0.5 mm thick.

Manufacturers produce galvanized or painted corrugated sheets. The cost of painted sheets is 20% higher than galvanized sheets, but their service life is longer.

You can read more about choosing a profiled sheet for a fence.

Construction of a fence made of corrugated sheets

A fence made of corrugated sheets with metal posts is a linear structure. Metal pillars reinforced in the ground in various ways are used as the base. To install gates, choose pillars with a thicker wall than for intermediate supports.

The pillars are connected to each other by horizontal metal logs or veins. For fences up to 1.5 meters high, it is permissible to install only two logs per span, at the top and bottom. If the fence is higher than 1.5 meters, add a third vein in the middle.

The corrugated sheet is attached to the logs with metal screws and rubber washers. The gate and wicket are hung on metal hinges, which are welded to the support post.

Required materials and tools

To install a fence from corrugated sheets, you will need the following materials:

• metal pipes for poles with a cross-section of 50 mm and a wall thickness of 2.5 mm;
• metal profile for veins, section 40x20 mm and wall thickness 1.5–2 mm;
• profiled sheet;
• self-tapping screws for metal with a rubber washer, size 5.5x20 mm.
• cement;
• sand;
• fine crushed stone.

To carry out work on installing a fence, you will need the following tools:

• bayonet shovel;
• electric or manual drill;
• a cord no less long than the total length of the fence;
• yardstick;
• construction level;
• plumb line;
• container for preparing the solution;
• screwdriver;
• electric drill with a set of metal drills;
• welding machine.

Calculation of the required amount of materials

Before you build a fence from corrugated sheets with your own hands, you will need to calculate the required amount of material.

When determining the number of corrugated sheets, the total length of the fence is divided by the width of one sheet. Please note that the useful width of the sheet is 1100 mm, while the standard sheet is 1155 mm wide. It takes 55 mm to overlap one sheet with another during installation - the width of one rib.

The length of the sheets depends on the height of the fence. Manufacturers produce sheets of standard sizes (2000 mm, 2500 mm, 3000 mm), but when ordering the material directly from the factory or from an official representative, you can order sheets cut to any size.

This is especially convenient when there are significant differences in height along the fence line and there is a desire to level the top line of the fence to one level, rather than installing sheets with ledges.

When calculating the number of screws, you need to proceed from the need for one sheet. The screws are tightened through one wave on each joist; accordingly, you need to count the number of installation locations for the screws along the width of the sheet, and multiply this number by the number of veins.

The number of pillars is determined based on the length of the fence line and the width of the spans. The recommended column spacing is 2000-2500 mm. If the length of the fence is 25 meters, then with a support installation step of 2.5 meters, 11 posts will be needed.

To determine the required number of lags, you should take into account the length of the metal profile and the method of fastening. If the profile is welded to the pillars, the optimal length of the lag is selected according to the multiplicity of spans.

For example, with a span width of 2.5 meters and a profile length of 5 m, one profile will be needed to cover two spans in a row. When cutting a profile to fit the span, you need to select the length of the material so that there are fewer scraps left.

Marking and excavation work

Do-it-yourself installation of a fence from corrugated sheets begins with markings:

1. Initially, you need to determine the extreme points of the site boundary. Already installed poles in neighboring areas can serve as a guide. If necessary, representatives of the cadastral chamber are called.
2. At the extreme points, pegs are driven in and a cord is pulled between them, which will show the line of the future fence.
3. The distance between the supports is determined taking into account the convenience of cutting the material for the frame, but the distance between adjacent pillars should not exceed 3000 mm. Focusing on the line of the cord, pegs are driven in to indicate the installation location of each support. For ease of marking, the installation points of the pillars are marked on a stretched cord. Then a thread with a weight is tied to these points, which will indicate the exact location for the hole for the support.

For ease of work, the marking plan is transferred to paper. The drawing will help you accurately calculate the amount of material and avoid confusion when installing the frame.

What material to choose for pillars

To support a corrugated fence, metal pipes with a round, square or rectangular cross-section are used. The minimum diameter of the pipe for the post is 50 mm, the wall thickness is at least 2.5 mm. When choosing material for posts, you should also take into account the wind load in the area where the fence is installed.

The length of the post is calculated taking into account the height of the fence and the part that will be in the ground. For heaving soils, it is recommended to go through the freezing depth. In other soils, the ratio of the height of the ground part and the part fixed in the ground is calculated as 2 to 1. For example, the height of the fence is 2000 mm, which means that immersion in the ground will be required by 1000 mm, and the total length of the post will be 3000 mm.

Installation of base for pillars

To prepare the base for the pillars, use the following step-by-step instructions:

1. dig holes for supports. You can dig with a regular bayonet shovel or a drill (manual or electric). The depth of the hole for the support must be at least 1000 mm (taking into account adding a layer of sand or gravel to the bottom in a layer of 100-200 mm). The width of the yaki should exceed the diameter of the post by a third;
2. sand or fine gravel is poured into the bottom of the hole. The pillow is carefully compacted.

The base for installing the support is ready.

Installation of pillars

After preparing the hole for the support, the installation of the pillars begins:

1. the part of the post intended for immersion in the ground is cleaned of rust, degreased, treated with a metal primer and painted over with bitumen mastic. Installation begins after the protective layer has dried;
2. the post falls into the hole;
3. check the height of the ground part of the pole. If necessary, adjust the height by removing excess sand or adding sand to the hole;
4. With the help of supports, the pole is installed strictly vertically. For this work, two people will be required: one adjusts the position of the pillar, and the second corrects the actions of the first, determining the position of the pillar by a plumb line;
5. to securely fix the support in the foundation, several pieces of angle can be welded onto the surface of the underground part of the pillar;
6. A cement-sand mortar is prepared for pouring the foundation in a ratio of 1 to 3 (one part cement to three parts sand). The volume of concreting is small, so the solution is stirred next to the hole in a small container; you can also use a sheet of iron or plywood;
7. the solution is poured into the space between the post and the edges of the hole. To obtain more durable concrete, crushed stone or brick fragments are added to the solution. Each layer is carefully compacted and punched with an iron rod to prevent the formation of air voids;
8. After pouring the solution, the position of the column is checked again and, if necessary, adjusted.

This completes the process of installing the pole. To carry out further work, you will have to wait 5-7 days for the solution to gain sufficient strength. It will take 28 days to fully gain strength.

Attaching the joists

After installing the pillars, they begin to form a frame for attaching the corrugated sheet. To do this, install horizontal connections - logs or veins. There are two ways to attach the veins to the supports:

• The veins are welded.
• The veins are secured with bolts to brackets pre-installed on the posts.

The veins are pre-cut to size, taking into account the distance between the corrugated fence posts. When joining individual joists on a pole, a gap of 5 mm should be provided.

Before fixing the veins on the pole by welding, the fastening points are cleaned of paint, and the rust is removed with sandpaper or a grinding machine.

To weld the logs at the same level, maintaining a horizontal position, you will need the help of a second person who will hold the metal profile in the desired position and check its level. Boil the connection along the entire length of the contact between the log and the pillar.

After the welding work is completed, you need to clean the fastening points. Remove scale and excess deposits. At this point, poorly executed seams are often discovered, they are welded and cleaned again.

After cleaning, the junction of the vein and the post is treated with a primer and painted.

When fixing the logs on the brackets, work begins with installing the holders themselves. The brackets are screwed to the posts using bolts or powerful metal screws, having previously drilled the mounting holes.

Holes for bolts are drilled in the brackets and on the joists. Place the logs in the holders, insert the bolts and tighten the nuts. The connection is ready. All that remains is to treat the bracket and the mounting location with a metal primer and paint it.

Fastening corrugated sheets

To install the corrugated sheet on a metal frame, use the following step-by-step instructions:

1. Preparation of material. If sheets of the same size are used, no preliminary preparation is required. If you need to adjust each sheet to size, mark and trim with an angle grinder. The protective film is removed before fastening, since after screwing in the screws, fragments of the film will be visible from under the rubber seal.
2. Displaying the first sheet. To immediately set the correct order for installing the corrugated sheet on the frame, you need to correctly install the first sheet. The permissible height of the extension along the upper edge above the vein is determined. The sheet is secured with one self-tapping screw at the highest point. Then the second edge is leveled and also secured with a self-tapping screw at the opposite extreme upper point. Next, the sheet is screwed completely in increments through the wave.
3. Installation of profiled sheets. After installing the first sheet, the others are fastened sequentially, with the obligatory check of the position of each sheet according to the level. If the position of even one sheet is disturbed, a failure will occur along the entire length of the fence. To install the profiled sheet, use metal screws with a rubber washer. It is important to maintain the optimal level of tightening: the rubber washer must fit snugly to the base. If the washer is pressed in, the self-tapping screw is tightened; if the washer does not fit tightly to the base and rotates, the self-tapping screw is not tightened.
4. Installation of the plank. When building a fence from corrugated sheets with your own hands, you must not forget about protecting the top part of the material. To make the fence last longer, the upper ends of the sheets are covered with a special fence strip, 30 mm wide. To fix the strip, rivets with a head matching the color of the sheets are used.

Construction of gates and wickets

The installation of a corrugated fence is completed with the installation of gates and wickets. Metal posts with a wall thickness of 3.5 mm or more are used as gate supports. Reinforced garage awnings are welded to the posts.

The frame for gates and wickets is made from a profiled pipe with a cross-section of 20x40 mm and a wall thickness of 2 mm. After hanging the frame of the gate and wicket, they begin to install the corrugated sheet.

The corrugated sheet is fastened in the same way as when installing the main row of the fence. Locking devices are installed before installing the profiled sheet.

We have already written about the installation of swing gates in a fence made of corrugated board.

Video on the topic

Fences of various forms are an organic part of the vast majority of private garden plots. They not only protect the internal area from prying eyes, but also often perform a natural decorative function. In an effort to ensure a safe and comfortable life, owners order fences from all kinds of materials. One of the best options that meets most requirements would be to install a fence made of corrugated sheets.

In this article we will look at how to properly make a fence from corrugated sheets, and also discuss in detail the issue of choosing this material for a fence from corrugated sheets.

Classic fence and gates made of corrugated sheets Source vorota750.ru

What is corrugated sheeting

Corrugated sheeting (profile sheet or metal profile) is a common and popular roofing material due to its advantages. Being a product of cold rolled metal, it is a sheet of rolled galvanized steel that has passed through a roll forming machine. As a result, the surface of the sheet becomes wavy, reminiscent of slate, and the waves themselves form stiffeners.

Waves (corrugations) can have different heights and structures: sinusoidal, rectangular, trapezoidal.

Manufacturers apply polymer and paint coatings (polyester, plastisol or pural) to the finished sheets, which perform protective and aesthetic functions.

Profiled sheets do not need to be additionally painted or processed in any way Source gx.net.ua

Online fence calculator

To find out the approximate cost of a corrugated fence, use the following calculator:

Corrugated fences: pros and cons

As a fence material professional sheeting is chosen because of its positive qualities:

• Affordable price (they are much cheaper than wood or stone) with a decent appearance.
• Strength and wear resistance (treated with special compounds that reliably protect it from negative factors of natural origin).
• Lightweight material, which facilitates transportation and installation of the fence.
• The construction of fences from corrugated sheets is time-consuming.
• Comfort in operation (barrier from dust and noise, especially near the roadway).
• Mechanical strength.
• Environmental friendliness and fire safety.
• Unpretentiousness; an individual part can be replaced without dismantling the entire structure.

For any design of a fence made from corrugated sheets, individual sheets can be easily replaced Source rmnt.net

• Practicality (does not require annual painting, dirt can be removed with a damp cloth).

But we also need to take into account disadvantages of using corrugated sheets:

• Large windage. Sheets can bend and become deformed in strong gusty winds.
• The sheets are coated with a compound that protects them from rust, but the joists and posts are made of steel profiles. At the attachment points, even with a primer, metal corrosion begins over time.
• It is difficult to carefully paint the joists without touching the main sheet.

What are the types of corrugated sheeting for fences?

The material is selected according to the conditions of future operation and the wishes of the owner. The manufacturer offers corrugated sheeting in a variety of colors and imitations of natural materials.

Fence made of corrugated sheets, stylized as stone Source www.msk-novostroyka.ru

Varieties by coating:

• galvanized standard sheet;
• sheet with polymer coating, painted (plastic and synthetic resins);
• sheet coated with plastisol or polyester with increased wear resistance.

Sheets also differ in markings(steel thickness, type, width, wave height are marked):

• N – load-bearing profiled sheet intended for roofing work.
• C – wall sheet, suitable for the construction of fences and walls. By the number you can find out the height of the corrugation in mm (C10, C21, C20).
• NS is a universal-purpose sheet suitable for any construction work.

Additionally, profiled sheets are marked with the letters A and R. For fences, A-profiles are used (they are intended for painting on one side)

What you will need for installation: materials and tools

Materials included in the estimate:

• Profiled sheet of the selected brand.
• Metal pipes (used as support posts).
• Pipes for guides (standard steel profiles).
• Consumables (dowels, screws or rivets).
• Ruberoid to protect the holes from soil shedding (if the pillars are decided to be concreted) and a primer to protect the fastening points.
• Ready-made concrete, or its components - sand, crushed stone and cement (if the solution is mixed by hand).

If it is necessary to install a fence on a slope, the profiled sheet will have to be additionally processed Source zavodsota.ru

In addition to materials Tools will be required:

• Rope, nylon thread and wooden stakes for preliminary marking.
• Tape measure (minimum 4 m) and building level.
• Hand drill (replaced with a shovel).
• Welding machine for mounting the frame.
• Drill, screwdriver.
• Metal scissors, grinder, sledgehammer.

Development of a fence diagram and drawing

Before starting construction work, a graphic sketch (diagram of a fence made of corrugated sheets) is developed and a detailed drawing is drawn up. For this:

• The perimeter of the fenced area, topography and soil properties are clarified.
• Measure slopes.
• Insurmountable obstacles along the fence path (pipelines, electrical poles) are noted.

You need to ask the builders whether they make similar measurements. If not, then they are unlikely to be able to choose the right type of foundation, material of supports, joists and fasteners.

Standard layout of the fence site. Source prometr.com.ua

Marking the fence line

Marking begins with driving corner stakes into the corners of the territory. They fix the location of the support pillars. Additional stakes are driven in at the breaking points of the future fence.

Video description

About the initial stage of building a fence from corrugated sheets in the video:

Installation of support pillars

The work begins with the placement of support (corner) and auxiliary (in bending places) pillars, on which the height from the ground is marked. The post must enter the ground until the mark aligns with the stretched string. It is also necessary to regularly check the vertical position of the pillar with a level.

As supports for fastening corrugated sheeting, choose a profiled or ordinary pipe, reinforced concrete or wooden pillars, and screw piles.

The supports are fixed in the ground by concreting the base or driving it in. It must be remembered that a third of the length of the pillar is buried. During operation, it is necessary to control the verticality of the supports.

Detailed diagram of installation of a fence made from a profile sheet. Source plus.google.com

Lag fasteners

After installing the main and intermediate supports, the crossbars (joists) begin to be installed. They are attached parallel to the base of the fence, retreating 20-25 cm from the edge of the profiled sheet. The frame for a fence made of corrugated sheets is mounted according to the rule: 1 log per 1 m of structure height. On a fence up to 1.7 m high, it is recommended to fasten logs in 2 rows, over 1.7 m - in 3 rows (to increase the rigidity of the structure).

To install the logs, 2 types of fastening are used:

• Welding. The fastest and most reliable method. Welding areas are coated with a primer to prevent rust.
• Screw. Allows for dismantling.

Painting a frame for a profile sheet fence Source obustroeno.com

Installation of sheets

The corrugated sheets are fastened to the transverse joists using screws. It is necessary to monitor the fastening of the screws.

An incorrectly installed (strongly or crookedly twisted) screw when installing a corrugated sheet on a fence can deform the metal and cause corrosion.

The joint is overlapped through the wave and fixed with roofing screws or rivets (preferably steel, not aluminum).

How much will the fence cost: installation price

The total cost of fencing made from corrugated sheets consists of the total costs of materials, services for their delivery and installation of the structure.

The price of a corrugated sheet is determined by its thickness, the nature of the coating and the profile height. Delivery costs are determined by the distance to the construction site. The cost of installation work varies depending on the terrain and project characteristics.

The main value that influences the final amount is the height of the fence, which determines the size of the post and the depth of its placement in the ground, as well as the number of logs (cross members). You can calculate the required number of sheets by dividing the total length of the fence by the working profile sheet. Self-tapping screws are purchased based on the number of corrugated sheets. 9-10 self-tapping screws are taken per sheet.

On average, you can find the following prices on the market:

• A fence made of corrugated sheets with metal posts 1.5 m high - from 1000 rubles. per linear meter, height 2 or more meters (on three logs) - from 1200 rubles. per linear meter.
• A fence made of corrugated board with brick pillars - from 1400 and 1700 rubles, respectively. per linear meter.

Video description

Examples of beautiful fences made from corrugated sheets in the video:

A metal fence made of corrugated sheets serves as a laconic and popular way of fencing a private plot of land. It is in demand due to low monetary and labor costs; basic construction skills are enough to build it.

The construction of fences today is subject to requirements for strength, reliability and stability. At the same time, aesthetics play an important role in choosing a fence for a summer cottage. The fence should not only be durable and strong, but also fit harmoniously into the overall design.

A universal material for constructing a fence is considered to be corrugated sheeting, which is based on a galvanized metal sheet. Previously, profiled sheets were used only for covering the roofs of non-residential buildings, garages and for fencing construction sites. But this is already in the past.

Profiled sheet

Modern manufacturers of corrugated sheets have brought it to a higher level of quality. And today, corrugated sheeting is the same galvanized metal sheet, covered with high-quality protective layers, corrugated on a special machine and attractive in appearance. It is manufactured by using cold rolling, hot galvanizing and coating the surface with various protective compounds:

1. applying a protective layer of aluminum-zinc is considered the simplest and cheapest method, which provides acceptable strength and protection against corrosion. This material is suitable for covering a garage, outbuilding and small fence;
2. coating with a polymer composition, which provides higher protection and allows you to paint corrugated sheets in any color;
3. application of plastisol, which will provide the profiled sheet with maximum strength and durability.

Due to the fact that corrugated sheeting has a corrugated shape, it is durable, rigid and resistant to damage and wind.

Advantages of a fence made of corrugated sheets

Constructing a fencing site from profiled sheets with your own hands has a number of advantages:

• As a rule, fences made of corrugated sheets are installed faster than fences made of brick and natural stone; their installation does not require expensive equipment or special knowledge and skills. It is only necessary to correctly calculate the perimeter of the site, the amount of consumables and install support pillars. To give the fence an attractive appearance, you can also use brick, natural stone, and forged elements;
• the ability to combine with other building materials, including chain-link mesh;
• regardless of the height of the fence, its strength and reliability remain the same;
• sound insulation property allows you to protect the area from extraneous noise;
• environmental Safety;
• rich color range. At the same time, the corrugated sheets do not lose their color, do not fade or fade throughout their entire service life.

In addition, a fence made of corrugated sheets is cheap. But, most importantly, you must strictly adhere to all the rules on how to make a fence from corrugated board with your own hands.

Required tools and materials

Before building a fence from corrugated sheets, you need to prepare all the building materials and tools. To calculate the number of profiled sheets, it is enough to know the length of the fence around the perimeter of the site and add it to the height of the fence. You will also need:

1. profile pipes for support posts 60x60 mm. Of course, as supports for profiled sheets, you can choose pillars with brickwork, stone pillars, logs, and asbestos pipes. But when building a fence from corrugated sheets with your own hands, as a rule, pipes are used, the number of which is calculated as follows: the distance between the posts should not exceed 2.5 meters, and the height of the pipe should be equal to the height of the future fence plus the burial depth:
   
   The data obtained is added up and the result is the required number of pipes;
2. profile pipes 20x20 or 20x40 mm, which are necessary for installing crossbars for fastening sheets:
   
   The number of such pipes depends only on the height of the future fence;

IMPORTANT! It is impossible to use aluminum rivets to connect sheets of corrugated sheets, because they do not withstand loads well.

1. drill and building level;
2. welding machine and electrodes for creating a frame;
3. solution container, cement, crushed stone and sand;
4. rope and wooden pegs;
5. paint for painting posts and cross beams to match the color of the fence.

After installation, the fence will look like this:

Installing a corrugated fence with your own hands

Perimeter marking

Before you start building a fence from corrugated sheets, you need to correctly measure the perimeter of the fenced area and calculate the number of support pillars. Marking the territory is carried out by driving pegs in the corners of the future fence, between which a strong thread is pulled tightly, and the necessary measurements are taken. Only after this is a project for the future fence made of corrugated sheets drawn up.

Installation of support pillars

Before proceeding directly to the installation of pipes for the fence supports, it is necessary to dig holes around the perimeter for pouring the foundation. Of course, you can dig with a shovel, but this is a labor-intensive process. Therefore, it is better to use a garden auger. After each hole dug, the distance is measured and the next hole is dug. And so on.

The reliability, durability and appearance of the future fence will depend on how well the support posts are installed around the perimeter of the site.

The height of the supports for a corrugated fence depends on the height of the fence itself. The supports should be placed strictly straight, and the distance between them should be up to three meters. And in order to install pipes, it is necessary to dig holes 1-1.5 m deep.

IMPORTANT! The higher the fence, the deeper the holes should be.

After all the holes for the support pillars have been dug, you can begin installing the supports themselves, during which it is important to constantly ensure that they are strictly vertical. To do this you need to use a building level. If the support pillars have been installed straight and vertical, then you can start pouring concrete. Those pipes that will be lowered into dug holes 1.5 meters deep are filled with solution only to a meter, and the remaining 50 cm of pipes must be tightly wrapped with roofing felt, and then filled and compacted with sand. The foundation must be left in this state for three days.

IMPORTANT! The concrete mortar poured into the support holes should definitely be pierced using available materials. This is necessary to release the air that remains in the solution.

Mounting support beams

After the support pillars have been installed and the foundation has been firmly strengthened, you can begin installing the transverse joists, which are placed parallel to each other.

In order to securely attach the logs to metal poles, it is best to use a welding machine.

There is a second way to fasten the joists - using bolts and nuts, but it is not as reliable as welding.

IMPORTANT! The support logs should be attached to the posts at a distance of at least 20 cm from the top edge of the support post and from the surface of the ground.

Fastening corrugated sheeting to a metal frame

The construction of a corrugated fence is completed by the installation of the profiled sheets themselves, which are attached to the frame slats using self-tapping screws, rivets or galvanized bolts. As a rule, sheets should be joined with an overlap on one wave.

A fence made of corrugated sheets is the optimal solution for protecting the territory of a country house or cottage from prying eyes and unauthorized visits. Fences made of this material last at least 30 years. The metal profile is extremely easy to process, and the simple installation method allows you to install a fence around a house or summer cottage quickly and with your own hands, without involving additional labor. Possessing high performance characteristics and durability measured over decades, the metal profile also performs a decorative function, with the help of which you can ennoble a private area, making it not only inaccessible to prying eyes, but also homely.

Construction of a metal profile fence: pros and cons

A distinctive feature of metal profiles (profiled sheets, corrugated sheets) is versatility. In addition to the arrangement of roofing slabs and the construction of temporary utility structures (hangars, sheds, garages, etc.), this material is widely used in the construction of fences and enclosures for various purposes.

The metal profile is made from cold-rolled sheet steel, which, using a special technology, is coated with a layer of zinc and a protective polymer film of various colors. The thickness of the profiled sheet is 0.4–1.2 cm. At the final stage of production, the sheet, laid in rolls, receives a certain profile (trapezoid or wave) using roll forming equipment (manual or automatic).

Good to know: The steel base and stiffening ribs provide increased resistance of the material to deformation and force, and galvanization and polymer coating reliably protect the corrugated sheet from rust and mechanical wear.

For the construction of fences, profiled wall sheets with a profile height of 8 to 44 mm are used. The final cost of the material is influenced by such parameters as:

• thickness of the steel base;
• availability and quality of galvanization;
• quality of polymer coating;
• profile shape and height.

Advantages of metal profiles

The main advantages of using corrugated sheets in the construction of fences and fences include:

1. High performance characteristics.
2. Low specific gravity.
3. Ease of processing and installation.
4. Durability and resistance to aggressive operating factors.
5. Relatively low cost of material.

The corrugated sheet is well protected from rust, deformation, damage and climatic factors. The material is produced in a wide range of sizes, which allows it to be used for the construction of fences of any height and length.

Good to know: The lightness of the profiled sheet, as well as its mechanical rigidity, greatly simplifies the installation process. In addition, when building a fence from this material, the requirements for the strength of the supporting frame are reduced.

Disadvantages of wall corrugated sheets

The disadvantages of metal profiles used in the construction of fences and enclosures include:

1. Low level of sound insulation (a fence made of corrugated sheets will not be able to protect the internal area from noise coming from the street).
2. Low resistance to destructive influences (a fence made of such material can easily be broken through, say, by a heavy car, or a hole can be cut in it using a special tool for subsequent penetration into the fenced area).
3. Low presentability (corrugated sheeting is significantly inferior in visual appeal to traditional materials used in the construction of fences: wooden and plastic picket fences, metal, brick or stone).

Good to know: Despite the obvious disadvantages, corrugated sheets have no equal in terms of efficiency and are absolutely fire resistant. The material is available in a wide range of colors and a wide range of profile shapes and sizes, which allows you to satisfy almost any aesthetic needs of the buyer.

Photo: types of fences, ideas for implementation on the site

Profiled sheets as decorative cladding on entrance gates
Fence made of metal profiles on metal supports: view from the inside
Decorative design of corrugated sheets as part of a country fence
Fence made of metal profiles with decorative design: view from the inside
Fence made of corrugated sheets with decorative design
A fence made of corrugated sheets on a site with a slope
Corrugated fence with brick pillars
Metal profile fence on a concrete foundation

Fence design and preparation for construction

It is necessary to carefully prepare for the construction of a metal profile fence. Errors during the design and installation process are unacceptable, since they entail unplanned costs of time, nerves and money.

In order for the construction of the fence to be carried out quickly and not take an unreasonably large amount of effort and resources, at the preparatory stage of construction it is necessary:

1. Decide on the type and required characteristics of the metal profile.
2. Develop a construction project.
3. Calculate the required amount of materials.
4. Prepare a set of tools and auxiliary materials necessary for construction.
5. Carry out precise marking of the fenced area for construction, taking into account the location of gates, entrance gates, terrain slope, etc.

It is important to remember: After purchasing and delivering the main material to the construction site, it must be carefully stacked and covered to protect it from premature wear and climatic factors before installation work. The location of the stacks should not interfere with the passage, passage or placement of other building materials, elements of building structures, transport, etc.

Which corrugated sheet should I choose?

If the decision to build a fence from a metal profile has been made, all that remains is to choose a material that is suitable in terms of cost and quality. To do this, it is necessary to determine the requirements regarding its protective characteristics, as well as the reliability, durability and resistance of the future fence to wear and damage.

But first it won’t hurt to pre-install:

• conditional life of the fence;
• priority on aesthetics of appearance or operational reliability;
• design features of the fence and the possibility of replacing its individual elements during operation.

The list of key factors determining the choice of profiled sheet for fence construction includes:

1. Brand of material.
2. Steel thickness.
3. The quality of galvanization of the steel base of the corrugated sheet.
4. Type of polymer coating.
5. Sheet sizes and profile parameters
6. Price-quality ratio.
7. Durability and wear resistance.
8. Aesthetic preferences of the owner of the fenced area.

Profiled sheet marking

The metal profile has a special marking, which determines its main characteristics and purpose. So, for the construction of a fence, grade C (wall) or NS (universal) material is suitable. The numbers in the marking of the profiled sheet mean:

• profile height in mm;
• usable sheet width;
• thickness of the steel base.

It is important to remember: The thicker the steel base and the higher the zinc content in the protective layer, the more resistant to corrosion and deformation the corrugated sheet is. However, nowadays galvanizing technology is used less and less in the production of materials. A much more reliable protection against corrosion, damage and wear is a special polymer coating, which, moreover, can be given a color and even texture that matches the purpose of the metal profile.

Polymer coating and price/quality ratio

The polymer can be applied on one or both sides of the sheet, which significantly affects the overall cost of the material. In addition, the price of the metal profile is determined by the type of this polymer coating:

1. Polyester (PE) - film thickness is about 25 microns. The coating is used to protect the inner surface of the material. The film has low resistance to mechanical damage and ultraviolet radiation, which is compensated by the low cost of the profiled sheet.
2. Matte polyester (PEM) is a 35 micron thick coating characterized by its lack of shine and resistance to direct sunlight.
3. Pural is a protective film about 50 microns thick. It is characterized by elasticity, a high degree of anti-corrosion protection and excellent color quality.
4. Polyvinyl fluoride (PVF, PVDF, PVF2) is a coating with high strength and elasticity. Meets increased operational requirements, having excellent resistance to ultraviolet radiation, as well as rust and mechanical damage.
5. Plastisol (PVC200) is a universal film with a thickness of 200 microns, designed to protect surfaces of any type. It has high decorative qualities and elasticity, providing reliable protection of steel from corrosion.

Important to know: The dependence of price on the type of polymer coating, which largely determines the durability and wear resistance of the material, is obvious. The greatest demand in the construction of fences and barriers is metal profiles coated with matte polyester, which has an optimal price/quality ratio. Material coated with pural is also popular, since the latter provides not only high aesthetic performance of the corrugated sheet, but also increases the service life of the fence.

Profiled sheet parameters

The strength of wall corrugated sheeting depends not so much on the thickness of the steel base (0.1 cm is enough for building a fence), but on the size, shape and thickness of the ribs (waves) of the profile. Therefore, when purchasing, the main attention should be paid to the height of the latter. For the construction of a fence in an area with normal wind loads, a material with an edge whose height does not exceed 21 mm is suitable. As for the required sheet sizes and amount of material, they are determined based on the required height of the fence, as well as its perimeter. It should be taken into account that the corrugated sheet will be mounted with an overlap.

For the construction of fences and enclosures, four grades of wall corrugated sheeting are used. Their design parameters are given in the table:

Good to know: Wall corrugated sheets are produced in sheets 12 m long, but before sale they are cut into pieces 2–3 m long that are more convenient for transportation and installation.

Correct fence design and calculation of materials, diagram

Before you go to a hardware store to buy materials, you should correctly calculate their quantity, as well as determine the amount of work to manufacture the main elements of the fence structure. This can only be done if there is a detailed project. The latter is easy to develop independently, without involving expensive specialists.

The first and main thing that is necessary for design is the value of the perimeter of the fenced area. If it is not indicated in the cadastral plan, you will have to measure it yourself. For this you will need:

• hammer marks (metal or wooden pegs) into the ground at the corners of the site, as well as at points where the fence changes direction;

• tie the tags with nylon or linen cord;

• calculate the length of the cord between the marks, which will correspond to the perimeter of the area.

The next step is to determine the location and required dimensions of the entrance gates and wickets. It is necessary to place marks on the sides of the latter, measure the distance between them and subtract the resulting value from the total perimeter.

Calculation of the number and sizes of sections

1. For example, let’s assume that the plot has a rectangular shape with sides of 20 and 15 m. Let’s take the width of the gate equal to 2.5 m, and set the value for the gate to 1.5 m. In this case, the length of the fence will be equal to: L=(20+15) *2 - (2.5+1.5)=66 m.
2. The standard length of the profiled sheet is 12 m, so for ease of transportation and installation it will have to be divided into segments. Therefore, at this stage it is necessary to calculate how many segments will fit in one section along the length.
3. We will establish that the gate will be located next to the gate on the 20-meter side of the perimeter. In this case, the length of the fence in this area will be equal to: l=20–4=16 m. Thus, we take the number of sections equal to 3 meters: 2 sections will have a 5-meter length, and the size of the remaining one will be 6 m.
4. If we take the length of the sections on the opposite side of the perimeter to be 5 m, their number here will be 4.
5. It remains to calculate the number of sections on 15-meter segments of the perimeter. The calculation is carried out in a similar way: we take the length of the section to be 5 m. This means that the width of the rectangle will result in only 6 sections - 3 on each side.
6. Let's calculate the total number of sections: n=2+4+6+1=12+1. Thus, the fence will have 12 sections 5 m long and one 6 meter section adjacent to the gate.

Calculation of supports

Having the number of sections, we calculate the required number of supports using the formula:

It follows from this that to install the fence you will need: K=13+1=14 supports.

Important to know: It is convenient to use a profile pipe of square (50*50 mm) or round (d=50 mm) cross-section as support posts for a fence made of corrugated sheets. It should be noted that the length of the supports is a composite value. The outer part should be at least 10–15 cm longer than the corrugated sheet. This is necessary to leave a gap of 5–10 cm high at the bottom and a headroom of about 5 cm in the upper part. So, for a fence 2 m high, the height of the supports will be 210–215 cm. For installation in the ground, another 80–120 cm will be required (depending on the type of soil, freezing depth and groundwater level), and if the fence is installed on a strip foundation - 40–50 cm.

If the necessary requirements for the design of the supports are met, their length will be:

L og =200+15+80=295 cm (when installing supports in the ground);

L op =200+15+40=255 cm (when installed on a foundation).

Calculation of corrugated sheets

Using the height of the fence, as well as the number and length of sections, the required dimensions and number of profiled sheets are determined.

The height of the fence is equal to the length of the section of corrugated sheet. If the fence being designed has a height of 2 m, a standard 12-meter sheet will need to be cut into 6 2-meter pieces. If a profiled sheet of grade C21 is chosen for construction, each 5-meter section will require 5 such sheets and the remaining 6-meter section will require another 6 sections 1 m wide.

As a result, the total number of sections of corrugated sheets 2 m long will be:

N=n 5 *5+n 6 *6=12*5+1*6=66 ​​segments

where n 5 and n 6 are the number of 5- and 6-meter fence sections.

It is important to remember: Installation of the corrugated sheet is carried out with an overlap. This means that each sheet will lose a little length during installation. Thus, when calculating the number and size of sheets relative to the length of the section, the value of the joint size multiplied by 2 should be subtracted from the total length of the sheathing.

Calculation of transverse joists

For fences made of corrugated sheets, a metal profile pipe with a cross-section of 40*20 mm and a length corresponding to the dimensions of each section is used as transverse logs. At the same time, to install a fence 2 m high, you will need no more than 2 tiers of crossbars.

This means that the number of logs for the calculated fence will be:

k=k s *2=13*2=26 lag

where k c is the number of fence sections.

Final result

As a result of the research, it was found that to build a fence around the area in question it is necessary:

• 26 crossbars;
• 14 support pillars;
• 66 sheathing sheets, 2 m long.

Next, all that remains is to re-draw the diagram of the site and apply a projection of the fence on it indicating the number and size of sections, the location of gates and gates and other important data. The construction project can be considered ready.

Necessary tools and auxiliary materials

In order to independently make and install a fence from corrugated sheets, you need to prepare the tools in advance, which you cannot do without during the work process.

This list should include:

• bayonet and shovel;
• concrete mixer (if the fence is installed on a foundation or the supports will be installed on concrete);
• earth drill (for installing support pillars in the ground);
• electric scissors;
• metal scissors;
• electric drill with a set of metal drills;
• screwdriver;
• welding machine;
• circular saw with metal discs;
• construction tape;
• measuring cord;
• building level;
• plumb line

In addition to the basic materials of corrugated sheets and profile pipes for the manufacture of supports and transverse joists for the construction of the fence, auxiliary tools will be needed.

The list of the latter contains:

• sand;
• crushed stone;
• cement;
• primer for metal posts and crossbars;
• paint;
• metal screws or other fasteners for mounting the casing.

It is important to remember: When cutting metal, during the construction of a foundation or installing supports in the ground, as well as when installing crossbars and fixing profiled sheets, it is very important to follow safety precautions. This will avoid injury, as well as material damage and tool breakage. When performing work operations, you should use safety glasses, gloves and protective clothing. And most importantly: you need to prepare a free area for work, where nothing will interfere with the manufacture of fence elements, and supply electricity to it to connect power tools.

How to build a fence from corrugated sheets with your own hands: step-by-step instructions

After marking the territory and preparing materials, it’s time to start construction. The general algorithm of actions is as follows:

• pouring the foundation with installation of vertical supports on it;
• installation of support pillars in the ground;
• installation of transverse joists;
• priming and painting of the metal frame;
• installation of sheathing;
• decorative design of the fence.

Good to know: If the installation of the supporting frame is carried out by welding, the welds must be cleaned. You should also weld appropriately shaped plugs onto the support posts, which will prevent moisture from getting inside the pipe. It is better to make holes in the metal before assembly, although, if you have a powerful drill and a high-quality drill bit, they can be made after. It is advisable to apply primer and paint to the metal frame before installing the sheathing so as not to stain the new profiled sheet.

Laying the foundation for a corrugated fence

If the conditional service life of the fence exceeds 20 years or the nature of the soil or the layout of the site do not allow installation in another way, the fence is installed on a strip reinforced concrete foundation.

The foundation is poured in several stages:

Using a concrete mixer, a concrete solution is made from sand, crushed stone, cement and water, with which the trench is filled to the required level. During the process, you should periodically check the verticality of the support posts or fix it to the formwork with a lock made from waste boards.

It is important to know: The soil will not take moisture away from the concrete if the bottom of the trench is moistened abundantly before pouring. The finished foundation should be allowed to dry for at least 3 days, after which you can begin installing the transverse joists.

Installation of support pillars in the ground

If the fence is planned to be used for no more than 15–20 years, the fence is temporary, or the soil or layout of the site allows installation without pouring the foundation, the support pillars are installed in the soil.

There are several ways to install supports, the choice of which depends on the nature of the soil, the depth of groundwater and the height of the fence:

• driving;
• partial concreting (combined installation);
• butting (installation on a bed of sand and crushed stone);
• full concreting (with reinforcement);

The algorithm for installing fence supports in the soil looks like this:

1. Plugs are welded at the upper and lower ends of the supports, which will prevent moisture and soil from entering the pipe.
2. The corner supports and pillars along the edges of the gates and gates are installed first. In this case, it is necessary to carefully monitor the vertical level of the supports.
3. The installed corner posts are tied with twine or rope to mark the fence line.
4. The remaining support posts of the fence are mounted along the perimeter in the same way, observing the vertical level and the line set from the corner supports.

Important to know: To enhance the load-bearing capacity of concrete or partially concreted supports, the hole can be reinforced using thin (d=10 mm) reinforcement.

Installing fence supports on a sloped area

If the land has a slope, a number of additional steps must be performed when pouring the foundation or installing support pillars. In particular, with a slight slope, the soil should be simply leveled.

When installing a fence on a foundation on an area with an average slope, the procedure will be as follows:

When installing supports in the ground on a site with a slope, the depth of the holes is adjusted in the same way: the bottom of the hole of the first support of the next level should be at the level of the middle of the hole of the last support of the previous one.

Important to know: The difference in height levels should be the same along the entire length of the fence.

Installation of supporting frame

After installing the support pillars in the ground or on the foundation, the transverse joists are installed. They can be installed by welding or using special “crab” fasteners.

When installing on "crabs" in the supports and transverse joists, it is necessary to make holes of the appropriate diameter for bolted connections.

Installation of crossbars for welding is carried out in one of three ways: the logs are butt welded, on the sides of the support column, or fixed using a holder pre-welded to the support (a piece of U-shaped profile of the required dimensions).

Good to know: The location of the logs and the distance between them depends on the height of the fence. If the latter is 2 m, you need to subtract 40–50 cm from the upper edge of the support - the upper line of the crossbars will be attached at this level. Further down we retreat 100–120 mm and mark the level of installation of the lower logs. Then the distance from the lower cross member to the ground will be: l=200–40–120=40 cm.

Sheathing with metal profiles and finishing, painting the fence

If the installation of the frame is completed, and plugs are welded on top of the supports, you can proceed to the final stage of construction - cladding the fence. To do this, holes for fastening elements are made in the transverse logs with a pitch equal to the pitch of the profiled sheet. Before starting work, it is important not to forget to calculate the location of the joints of the metal profile; its sheets are attached directly to each other, bypassing the crossbars.

After installing the sheathing, the fence can be decorated with decorative elements. For example, by forging or beading along the upper and/or lower edge of the profiled sheet. You can also additionally protect the screw heads and bolted connections with special plastic plugs.

It is important to remember: When joining sheets with an overlap, installation is carried out on the upper wave of the profile. The corrugated sheet is fixed to the crossbars in the center of the lower wave of the profile.

The construction of a fence from corrugated sheets requires thorough preparation and, most importantly, correctly performed calculations. Then, if you do not make gross mistakes during installation, the work will not take much time and effort. For example, to fence an area with a perimeter of 60–70 m, it will take only 3–4 days, of course, provided that you don’t have to dig a lot to level the soil. The result should be a reliable and durable fence that will serve as excellent protection for the site from prying attention and will greatly complicate unauthorized entry into the fenced area.